Crestron DMPS-100 Especificaciones descargar pdf (Pagina 6)

DMPS-100-C DigitalMedia

™

Presentation System 100

crestron.com

800.237.2041

SPEAKER OUTPUT 70/100V: (1) 2-pin 7.62mm 15A detachable

terminal block;

Transformer-isolated 70 or 100 Volt mono speaker-level audio output;

Wire Size: Terminals accept up to 14 AWG;

Output Power: 40W RMS mono at 70 or 100 Volts;

Note: 4Ω/8Ω and 70/100V outputs are mutually exclusive

PROG OUT: (1) 5-pin 3.5mm detachable terminal block;

Balanced/unbalanced stereo line-level audio output;

Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;

Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced

AUX OUT 1: (1) 5-pin 3.5mm detachable terminal blocks;

Balanced/unbalanced stereo line-level audio outputs;

Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;

Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced

HDMI OUTPUT 1: (1) 19-pin Type A HDMI female, digital video/

audio output;

Signal Types: HDMI, DVI

[2]

;

Note: HDMI and DM Outputs function in parallel

DM OUTPUT 1: (1) 8-pin RJ45 female, shielded;

DM 8G+ output, HDBaseT compliant;

PoDM and PoH PSE (Power Sourcing Equipment) port

[4]

;

Connects to DM 8G+ input of a DM receiver/room controller or other

DM device, or to a HDBaseT device, via CAT5e or Crestron

DM-CBL-8G cable

[3]

;

Note: HDMI and DM Outputs function in parallel

Connectors - Control & Power

IR/SERIAL OUT 1 – 4: (4) 2-pin 3.5mm detachable terminal blocks;

IR/Serial output ports;

IR output up to 1.2 MHz;

1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud

IR IN: (1) 3-pin 3.5mm detachable terminal block

For connection of the CNXRMIRD IR Receiver

[1]

;

Allows control from IR wireless remotes using RC-5 command set

INPUT 1 – 4: (1) 5-pin 3.5mm detachable terminal block;

Comprises (4) programmable digital inputs;

Input Voltage Range: 0 to 24 Volts DC, referenced to GND;

Logic Threshold: 2.5 Volts DC nominal with 1 Volt hysteresis band;

Input Impedance: 10k Ohms at >5 Volts, 1M Ohms at <5 Volts;

Pull-up Resistor: 2.2k Ohms per input

RELAY 1 – 4: (1) 8-pin 3.5mm detachable terminal block;

Comprises (4) normally open, isolated relays;

Rated 1 Amp, 30 Volts AC/DC;

MOV arc suppression across contacts

COM A – B: (2) DB9 male, bidirectional RS-232 ports;

Up to 115.2k baud, hardware and software handshaking support

NET: (4) 4-pin 3.5mm detachable terminal blocks;

Cresnet Master ports, paralleled;

Available Cresnet Power: 30 Watts

SERVICE: (1) USB Type B female, for factory use only

PoDM 48VDC IN: (1) 4-pin snap & lock power jack;

48 Volt DC power input for PoDM power pack

[4]

;

Enables PoDM and PoH power sourcing

100-240V~4.0A 50/60Hz: (1) IEC 60320 C14 main power inlet;

Mates with removable power cord, included

G: (1) 6-32 screw, chassis ground lug

LAN: (1) 8-wire RJ45 female;

10Base-T/100Base-TX/1000Base-T Ethernet port

COMPUTER (front): (1) USB Type B female;

USB computer console port (cable included)

LCD Display

Green LCD alphanumeric, adjustable backlight, 2 lines x 20 characters per

line; Displays input/outputs by name, volume levels, setup menus, signal

routing, device info, and other system information

Controls & Indicators

NET: (1) yellow LED, indicates Cresnet bus activity

LAN: (1) yellow LED, indicates Ethernet activity

HW-R: (1) recessed miniature pushbutton for hardware reset, reboots the

control system

SW-R: (1) recessed miniature pushbutton for software reset, restarts the

SIMPL program

POWER: (1) pushbutton and green LED, programmable for system

power control

SOFTKEYS: (4) pushbuttons for activation of LCD driven functions and

passcode entry

MENU: (1) pushbutton, steps menu back one level

, : (2) pushbuttons, scroll up or down through menu and adjust

menu parameters

ENTER: (1) pushbutton, executes highlighted menu or value

VOLUME: (1) continuous turn rotary encoder, adjusts menu parameters,

defaults to Program audio volume

MUTE: (1) pushbutton and red LED, mutes the Program audio output

ROUTE: (1) pushbutton and red LED, selects ROUTE mode to allow

routing changes

VIEW: (1) pushbutton and red LED, selects VIEW mode to view

current routing

INFO: (1) pushbutton and red LED, selects INFO mode to view AV and

device info

INPUT 1 – 4: (4) pushbuttons and red LEDs, select input to be routed

OUTPUT 1, PROG, AUX 1: (3) pushbuttons and red LEDs, select

output destination(s)

SPEAKER OUTPUT: (1) 3-position slide switch, selects the amplifier

output configuration

DM OUTPUT 1 (rear): (2) LEDs, green LED indicates DM link status, amber

LED indicates video and HDCP signal presence

DM OUTPUT 1 PoDM (rear): (1) green LED, indicates downstream device

is drawing power over DM

LAN (rear): (2) LEDs, bi-color LED (left) indicates Ethernet speed and

1 2 3 4 5 6 7 8

Comentarios a estos manuales

Sin comentarios

Crestron DMPS-100 Especificaciones Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Proyectores Crestron DMPS-100