Crestron MLX-3 Manual de usuario descargar pdf (Pagina 2)

PMC3-XP Prodigy

Expander Control System

crestron.com/prodigy

crestron.com

800.237.2041

Range (typical): 150 ft (46 m) indoor, 250 ft (76 m) outdoor to nearest

Prodigy “EX” or infiNET EX

™

mesh network device(s); subject to site-

specific conditions and individual device capabilities

[3]

Device Support: Maximum 100 Prodigy “EX” and/or infiNET EX

devices (inclusive of up to 6 MTX-3/PTX3 and/or MLX-3/PLX3 remotes)

and 5 expanders (model CLW-EXPEX and/or P-EXPEX)

Video

(FUTURE)

Audio

Functions: Basic audio file playback, audio signal pass-thru w/mute

during file playback, global volume and mute control

Audio File Formats: WAV (8 & 16 bit PCM, mono & stereo, 8 – 44.1

kHz sampling rates), MP3, WMA

Input/Output Signal Types: Analog stereo (input for future use)

Analog-To-Digital/Digital-to-Analog Conversion: 24-bit 48 kHz

Performance (pass-thru): Frequency Response: 20Hz to 20kHz

±0.2dB;

S/N Ratio: >93dB, 20Hz to 20kHz A-weighted;

THD+N: <0.01%, 20Hz to 20kHz;

Stereo Separation: >91dB

Connectors

AUDIO IN, L – R: (2) RCA female, unbalanced stereo line-level audio

input;

Input Level: 2 Vrms maximum;

Input Impedance: 7k Ohms nominal

AUDIO OUT, L – R: (2) RCA female;

Unbalanced stereo line-level audio output with volume and mute

control;

Maximum Output Level: 2 Vrms;

Output Impedance: 100 Ohms nominal

VIDEO OUT, Y Pb Pr: (3) RCA female, component (YPbPr) video out-

put(for future use);

Output Level: 1 Vp-p nominal (Y), 0.7 Vp-p nominal (PbPr);

Output Impedance: 75 Ohms nominal

VIDEO OUT, COMPOSITE: (1) RCA female, composite video output(for

future use);

Output Level: 1 Vp-p nominal;

Output Impedance: 75 Ohms nominal

IR 1 – 5: (5) 3.5mm mini-phone jacks, IR/Serial output ports;

IR output up to 1.2 MHz;

1-way serial TTL/RS-232 (0-5 Volts) up to 115.2k baud

IR IN: (1) 3.5mm TRS mini-phone jack;

For connection of the CNXRMIRD IR receiver

[1]

;

Allows IR wireless control from Crestron and third-party remotes using

RC-5 IR commands

COM 1 – 2: (2) DB9 male, bidirectional RS-232 ports;

Up to 115.2k baud; hardware and software handshaking support

LAN: (1) 8-wire RJ45 jack (8P8C modular female);

10BaseT/100BaseTX Ethernet port

USB 1 – 2: (2) USB Type A female;

USB 2.0 ports for storage and mouse/keyboard devices

G: (1) 6-32 screw, chassis ground lug

RELAY 1 – 2: (1) 4-pin 3.5mm detachable terminal block comprising

(2) normally open, isolated relays;

Rated 1 Amp, 30 Volts AC/DC;

MOV arc suppression across contacts

INPUT 1 – 2: (1) 3-pin 3.5mm detachable terminal block comprising

(2) contact-closure or voltage-logic sensing inputs (referenced to GND);

Input Voltage Range: 0-24 Volts DC;

Logic Threshold: ≥1.2 Volts DC active/high, ≤0.46 Volt DC inactive/low;

Input Impedance: 2.2k Ohms pulled up to 5 Volts

NET: (1) 4-pin 3.5mm detachable terminal block, Master port for

Prodigy “NET” or Cresnet devices;

Sources power to Cresnet devices with power pack connected to

24VDC power input jack;

May be used as alternate power input to receive operating power from

the Cresnet network in lieu of a local power pack;

See “Power Requirements” for additional specifications

24VDC 2A: (1) 2.1mm barrel DC power jack, 24 Volt DC power input;

PW-2407W power supply included;

Passes through to NET port to power Cresnet devices;

See “Power Requirements” for additional specifications

COMPUTER (front): (1) USB Type B female;

USB 2.0 computer console port

Antenna (front): (1) Connection for supplied antenna

Controls & Indicators

PWR: (1) Green LED, indicates operating power supplied from power

pack or Cresnet network

NET: (1) Amber LED, indicates communication with the Prodigy “NET”

and/or Cresnet system

HW-R: (1) Recessed pushbutton for hardware reset

SW-R: (1) Recessed pushbutton for software reset

ACQUIRE: (1) Recessed pushbutton with red LED, used to set up con-

nections with wireless devices

ACTIVITY: (1) Red LED, indicates wireless communications

LAN (rear): (2) LEDs, green LED indicates Ethernet link status, amber

LED indicates Ethernet activity

Power Requirements

Power Pack: 0.7 Amps @ 24 Volts DC;

100-240 Volts AC, 50/60 Hz power pack, model PW-2407W included

Available Cresnet Power: 35 Watts (1.46 Amps @ 24 Volts DC) when

using PW-2420RU power pack (not included)

Cresnet Power Usage: 9 Watts (0.375 Amps @ 24 Volts DC) when

using Cresnet network power

Environmental

Temperature: 41° to 113°F (5° to 45°C)

1 2 3

Comentarios a estos manuales

Sin comentarios

Crestron MLX-3 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos Crestron MLX-3