Crestron Adagio ATC-AMFMSR Especificaciones descargar pdf (Pagina 3)

Adagio

AMS

Media System

quickstart guide

www.crestron.com

800.237.2041

Specifications subject to

change without notice

201.767.3400

For details, refer to the

AMS Operations Guide, Doc. 6509.

QUICKSTART DOC. 6510C (2015964) 07.13

Adagio

AMS

Apply Power

CAUTION: If you are adding Crestron

equipment beyond the devices mentioned in this

guide, be aware that insufficient power can lead to

unpredictable results or damage to the equipment.

Please use the Crestron Power Calculator, available

from the Crestron website (http://www.crestron.com),

to help calculate how much power is needed for the

system.

NOTE: The AMS, AAS, and AAE units do not have

a power switch. Power is applied to the units by

plugging in their respective power cords.

A. Connect the AC power cord to the AMS and,

if applicable, to the optional AAS and AAE.

Then connect the power cord(s) to AC power.

B. Connect power to all other system devices as

required. (Cresnet supplies power to the APAD

controller and the C2N-DBF12 keypads.)

Connect Grounds

Using 16 AWG wire with ground lugs (not

supplied), connect the ground terminals on

the rear of the AMS and the optional AAE to

a case screw on the rear of the optional AAS,

and to an earth ground. Chassis grounds

from external audio sources should also be

connected to the AMS ground screw.

Earth

Ground

AMS

AAS

AAE

Install Dual Tuner Cards

CAUTION: Tuner cards are electrostatic-sensitive devices. Wear

a grounding strap or touch the metal chassis of a known

grounded device before handling and installing cards.

CAUTION: Do not connect external sources to SOURCES

connectors used by installed tuner cards.

NOTE: Make sure that the power cord is not connected before installing

any tuner cards.

A. Remove screws securing the plate covering the card slot to be

used. Insert the tuner card into the slot side rails, and make certain card

is fully seated before using the attached screws to secure it in position.

B. Install tuner cards in Slots 1 and 2 only, for out-of-the-box functionality.

(One card may already be installed in Slot 1.) Either card may be

installed in either slot.

NOTE: The output of each dual tuner card occupies two of the ten

available source connections in the AMS. Slot 1 outputs are on

SOURCES 1 and 2, Slot 2 outputs are on SOURCES 3 and 4. After

installing the tuner card(s), the remaining connections may be used for

other audio sources.

C. Connect the antennas included with the tuner cards. Refer to the

guide included with the tuner(s) for details on connection and antenna

placement.

Slot 1 Slot 2

AMS

For Future

Expansion

Antenna

Sirius

Antenna

ATC-AMFM2

ATC-AMFMXM

ATC-AMFMSR

Connect the Optional Adagio Audio Expander (AAE)

The following steps can be performed in any convenient order. Steps A through D

are performed in the same way that similar connections were made to the AMS

(Step 4), and are not illustrated again here.

A. Connect previously installed 16 AWG minimum (up to 12 AWG) speaker wire

to the speakers in rooms 7 - 12. Observe the polarity of the wires to each

speaker.

NOTE: Use speakers that are rated for full available output. Do not connect more

than two 8-Ohm speakers in parallel to each output.

B. Connect the speaker wire from rooms 7 - 12 to the AAE ROOMS connectors

(Rooms 1 - 6) using the 2-pin socket connectors provided.

C. Connect the keypads (C2N-DBF12) or controllers (APAD) in rooms 7 - 12 to

previously installed Cresnet cables.

Speakers

From Rooms 7 - 12

Cresnet

From Rooms 7 - 12

Cresnet

AMS

AAE

D. Connect the Cresnet cables from rooms 7 - 12 to the appropriate NET connectors 1 - 6 on

the AAE (e.g., Room 7 to NET 1, etc.).

E. Connect the AMS NET and AAE NET LOOP THRU inputs using standard Cresnet cable.

available AAE SOURCES connector (default is 6).

NOTE: Specific connection to the AAE SOURCES connectors depends on the number and type

of optional audio sources used in the system. Refer to Step 3 and to the AMS Operations Guide

for details.

G. Analog sources connect to the AAE SOURCES connectors; the sources are then shared

with the AMS ANALOG SOURCES connectors through the AAE loop through inputs. The wiring

method shown here is standard practice, but connections can be made to either side of the AAE

connector set.

Theater Downmix

Theater

Downmix

NOTE: If the Theater Downmix output

is connected to an AAE SOURCES

input, do not connect that loop through

connection to the AMS.

F. Connect the AMS theater downmix from the AMS OUTPUT connectors to the appropriate

1 2 3 4 5

Media System 1
Adagio AMS 5

Comentarios a estos manuales

Sin comentarios

Crestron Adagio ATC-AMFMSR Especificaciones Pagina 3

Comentarios a estos manuales

Relacionado con productos y manuales para Estaciones de muelle de dispositivos móviles Crestron Adagio ATC-AMFMSR